I’m not always fast. I may be persnickety … detail-oriented … analytical … creative … organized (ha!) … but face it, oftentimes my techniques for making surprisingly durable jewelry are NOT fast. Until now.
I’m happy to share my 10-Minute Method of making a bangle in this free tutorial…
Step 1. Gather Materials
- Nunn Design® Bangle Bracelet Channel
- Digital image laser printed on Monica’s Matte Jewelry Paper
- E-6000 Adhesive
- plastic card (I’m using an empty gift card)
- non-stick clip
- nitrile gloves
Step 2: Print your digital image with a laser printer onto Monica’s Matte Jewelry Paper.
Note: Is my Matte Jewelry Paper really necessary? That depends. It is necessary if you want your bangle to be waterproof. But if you choose other paper (scrapbook paper or inkjet prints), you’ll need to seal your paper. The paper and sealer you choose will make all the difference. See my “Variations” notes at the end of this post for more info.
Step 3: Trim your printed art to 7.5mm wide and approximately 220mm long.
- Test the fit of your trimmed paper by wrapping it around the bangle.
- The trimmed paper should fit in the channel.
- The ends of the printed paper should overlap a bit, which makes adhering the paper a bit easier to do. The true circumference of the bangle is 216mm, so I usually add about 4mm for overlap.
Step 4: Apply E-6000 adhesive to the back of the trimmed paper.
- I prefer the mini .18-fluid-ounce E-6000 tubes. They are an easier size for me to use and I can easily squeeze a narrow line of glue on the trimmed strip. Your mileage may vary.
- A single, solid narrow line of adhesive will be sufficient. You’ll spread it in the next step.
- Follow all E-6000 safety precautions, such as “wear gloves” and “work in a well ventilated area”.
Step 5: Spread the E-6000 with a plastic card.
One swipe of the plastic down the length of the paper, in a squeegee type of motion, will give you a smooth layer of E-6000 on the back of the paper without any dry spots or lumps.
- Hold the paper in place as you spread the E-6000. Don’t let the E-6000 get on the printed side of your paper. It would smear the ink and leave gummy lumps. Not an attractive look.
- This is messy. Expect the E-6000 to smoosh off the edges of the paper and smear onto your work surface. You’ll also have a lump of adhesive under your plastic card. My favorite work surface for this is an oven liner. Seriously. In fact, I use oven liners during oodles of crafty techniques. I’ll blog about that another day.
Step 6: Apply the paper to the bangle.
Start by aligning one edge of the paper in the channel then use a finger to push the paper onto/around the bangle. You’ll be burnishing and applying all in one step, which ensures a smooth, bubble-free fit.
Step 7: Apply a non-stick clip or two where the edges of the paper overlap. Set aside to dry.
I can’t say exactly how long it will take the E-6000 to dry. I know temperature and humidity are important factors. According to the manufacturer, though, 24 – 72 hours is considered a “full dry time” for the product to be considered truly waterproof.
I tend to make bangles in the evening and usually wear them the next day (I’m so patient). The E-6000 has consistently held the paper together well enough for me. However, if you intend to immerse the bangle in water, I recommend you follow the manufacturer’s guide and wait a day or three.
Step 8: Congratulations! Your new bangle is finished. Enjoy!
If you sell jewelry at craft fairs and the like, this technique can be an easy table-filler for you. One printed sheet can yield 17 – 25 trimmed strips, depending on the art you choose and the efficiency of your trimming. I can trim and assemble 25 in an hour. That’s a fantastic creation timeframe for a hand-made product that looks amazing.
Are you curious about the art I used for the tutorial bangle? It’s one of my favorite bangles and it features part of a chromolithograph from the 1850’s. I adore the bright colors and intricate patterns. It’s from one of my favorite artists, Corinna of Piddix. You can read more about her art and why I prefer it in my Wanna Know a Secret post.
- My technique in this tutorial is pretty flexible. I’ve used liquid resin instead of E-6000 (still using my Matte Jewelry Paper). The resin gave the bracelet a very nice glossy effect because I coated both sides of the paper with the resin before applying it to the bangle.
- In a previous free tutorial, I showed you how to wallpaper a Nunn Design® Bangle with liquid resin. You can modify the wallpaper technique by using E-6000 instead of liquid resin. I’ve made a few wallpapered bangles with E-6000 and so far I’m pleased with the durability.
- One of my favorite adhesives is Glamour Glaze from Annie Howes. It’s a water-based adhesive that dries crystal clear. Soon, I’ll be experimenting with Glamour Glaze as a bangle adhesive. If you beat me to it, though, please share your experience. I love learning.
- If you use an InkJet printer and want to try modifying my technique to make bangles from inkjet-printed art, I suggest trying Glamour Seal (another Annie Howes product). I haven’t personally tried Glamour Seal but I trust Annie. If she says it seals well, I’m sure it does.